Відмінності між версіями «Soldering copper pipe»

Матеріал з HistoryPedia
Перейти до: навігація, пошук
(Створена сторінка: For those homeowners who require doing there own plumbing projects listed here is a little help guide help you with the soldering from the copper piping employe...)
 
м (Soldering copper pipe)
 
Рядок 1: Рядок 1:
For those homeowners who require doing there own plumbing projects listed here is a little help guide help you with the soldering from the copper piping employed in home plumbing systems. First I should point out that if you do your own personal pluming installations you have to have an over-all idea of the codes governing such installations. You can find the codes to your state on the link below.
+
For the people home owners who refer to doing there own plumbing projects this is a little help guide advise you regarding the soldering from the copper piping used in home plumbing systems. First I would explain that if one does your own pluming installations you ought to have a general idea of the codes governing such installations. You will discover the codes on your state in the link below.
  
  
  
[http://sweatingcopperpipe.com/ Sweating copper pipe] is not as difficult as many people think it is. The main requirement to some successful soldering experience is cleanliness. Thoroughly clean inside your connections with a wire reamer brush that you can buy at any hardware or plumbing supply store. Now cleanse the out side of your pipe no less than One inch after dark end from the fitting with emery cloth or steal wool. Additionally it is not always a bad idea to de bur inside the pipe with your pliers. Some pipe cutters come with a triangular blade stuffed of their back, it is a de burring tool. Put it to use to remove any debris left from cutting the pipe that will hinder the soldering and spark a leak.
+
[http://sweatingcopperpipe.com/ Soldering copper pipe] just isn't as difficult as a lot of people believe that it is. The main requirement with a successful soldering experience is cleanliness. Thoroughly clean within your connections with a wire reamer brush that you can buy at any hardware or plumbing supply store. Now cleanse the out side of the pipe at least One inch past the end with the fitting with emery cloth or steal wool. Additionally it is not always a bad idea to de bur inside the pipe with your pliers. Some pipe cutters come with a triangular blade herniated of the back, this is the de burring tool. Use it to take out any debris left from cutting the pipe that could hinder the soldering and create a leak.
  
The next thing is to make use of the flux. The flux provides for a cleaning and bonding agent so that the solder will adhere to the copper and form a fantastic tight and strong joint. Make sure you use the flux liberally and beyond the fitting to be certain no dirt or dry spots result in the solder to not stick properly.
+
The next thing is to use the flux. The flux provides for a cleaning and bonding agent so your solder will stick to the copper and form a great tight and powerful joint. Make sure to apply the flux liberally and past the fitting to be sure no dirt or dry spots increase the risk for solder to not stick properly.
  
After assembling your joint bring your torch and with the tip of the flame heat the very center portion of the fitting alternating sides for evenness. Using your solder extended touch the joint. Keep heating until the solder melts. Now get rid of the heat and melt about 3/4 of an inch of solder in the joint. Heat will draw the solder into the fitting throughout. You need to begin to see the solder being a ring throughout the entire joint. Now wipe off the excess having a rag as well as your done. Start working on another joint simply repeating precisely the same procedure.
+
After assembling your joint take the torch and with the tip of your respective flame heat the middle portion of the fitting alternating sides for evenness. Together with your solder extended touch the joint. Keep heating until the solder melts. Now eliminate the heat and melt about 3/4 of an inch of solder in the joint. The warmth will draw the solder in to the fitting all around. You ought to begin to see the solder as a ring across the entire joint. Now wipe off of the excess having a rag as well as your done. Move on to another joint simply repeating exactly the same procedure.

Поточна версія на 19:31, 26 листопада 2016

For the people home owners who refer to doing there own plumbing projects this is a little help guide advise you regarding the soldering from the copper piping used in home plumbing systems. First I would explain that if one does your own pluming installations you ought to have a general idea of the codes governing such installations. You will discover the codes on your state in the link below.


Soldering copper pipe just isn't as difficult as a lot of people believe that it is. The main requirement with a successful soldering experience is cleanliness. Thoroughly clean within your connections with a wire reamer brush that you can buy at any hardware or plumbing supply store. Now cleanse the out side of the pipe at least One inch past the end with the fitting with emery cloth or steal wool. Additionally it is not always a bad idea to de bur inside the pipe with your pliers. Some pipe cutters come with a triangular blade herniated of the back, this is the de burring tool. Use it to take out any debris left from cutting the pipe that could hinder the soldering and create a leak.

The next thing is to use the flux. The flux provides for a cleaning and bonding agent so your solder will stick to the copper and form a great tight and powerful joint. Make sure to apply the flux liberally and past the fitting to be sure no dirt or dry spots increase the risk for solder to not stick properly.

After assembling your joint take the torch and with the tip of your respective flame heat the middle portion of the fitting alternating sides for evenness. Together with your solder extended touch the joint. Keep heating until the solder melts. Now eliminate the heat and melt about 3/4 of an inch of solder in the joint. The warmth will draw the solder in to the fitting all around. You ought to begin to see the solder as a ring across the entire joint. Now wipe off of the excess having a rag as well as your done. Move on to another joint simply repeating exactly the same procedure.